
Pushback Rack in Memphis, TN
Pushback rack gives a Memphis warehouse two to six pallets of the same SKU behind a single pick face. Each lane rides on nested carts set on inclined rails: load from the front, and the next pallet nudges the earlier one back. Pull the front pallet and the rest roll forward.
That is last in, first out storage, and it fits the reserve stock that fills buildings along the Airport, Airways and Lamar Avenue corridor. Most of those older buildings run 20 to 24 feet clear, so depth often matters more than height.
Where Pushback Pallet Rack Pays Off Near the Airport
Air-cargo-driven distribution around Memphis International Airport and the FedEx World Hub tends to hold fast-moving repeat items. When a third-party logistics tenant carries twenty pallets of one product, giving each pallet its own aisle face wastes floor.
A three- or four-deep lane collapses several selective rows into one. You trade individual pallet access for fewer aisles, and in a low-ceiling building off I-240 that trade is usually where the added positions come from.
Mixed SKUs with one or two pallets each still belong in selective bays. We draw both in the same layout so you can see the split.


Operations We Rack Around Here
Nearby areas we work in regularly include the airport and I-240 distribution belt, Airport/Nonconnah, Frayser, Raleigh, Hickory Hill.
Matching Lane Depth to Pallets per SKU
The mistake I see most is lanes built deeper than the inventory. A five-deep lane holding two pallets leaves three positions you paid for and cannot use for anything else.
We start with your SKU list: how many pallets per item at normal levels, how many at peak, and how quickly each one turns. That count sets lane depth bay by bay, not one depth for the whole building.
If an item needs strict date rotation, pushback is the wrong answer. Compare pallet flow rack in Memphis, which loads one end and picks the other.
Reading a Memphis Pushback Layout Before You Buy
A good drawing answers three things: how many positions you gain, which aisles disappear, and which items move. If a layout cannot show those clearly, it is not finished.
In Southwest Memphis, river and rail users on President's Island often store inbound material in big lots that wait for production or outbound loads. Those lots are natural candidates for three- and four-deep lanes beside the dock doors.
Healthcare distributors near Hickory Hill run a different profile. Many items, modest quantities, frequent picks. There we might convert only a handful of runs and leave the rest single-deep.
We mark carts per level, beam elevations and the clearance your truck needs to place a load at the highest cart. That detail prevents surprises during the first week of use.
Push Back Racking in Older Lamar Avenue Buildings
Older buildings near the BNSF intermodal facility on Lamar Avenue often have tighter column grids. Lane widths and frame lines have to land between columns, so we measure the grid before choosing bay sizes.
Carts need a sound pallet bottom and a load inside the rated range for each level. Beams and frames are sized to your heaviest pallet, and the system is anchored to the floor.
Summer heat inside non-air-conditioned buildings is real. Installation crews we schedule and manage plan early starts and staging so receiving stays open.
Common Errors We Correct in Memphis Bids
Older bids we review sometimes show pushback lanes at one fixed depth across a whole building. Real inventory is rarely that uniform, and the mismatch shows up as dead positions within months.
Another frequent gap is ignoring the lowest overhead obstruction. Lights and joists in Airways-area buildings sit lower in places, which can cancel a planned level.
We redraw those details before a single frame is ordered, so the pushback rack you buy matches the building you actually have.
Pushback Versus Drive-In for Bulk Stock
When one SKU runs ten or more pallets deep, a forklift-entry system may hold more. See drive-in rack in Memphis for that comparison. Drive-in removes carts but slows putaway because the truck enters the lane.
Memphis Pallet Rack is a division of Warehouse Equipment & Supplies Co., supplying and installing rack since 1997. Read the pushback rack product overview or return to our Memphis service area page.
Recent Installations
Racking projects completed for warehouses across west Tennessee, north Mississippi, and eastern Arkansas.










Get a Pushback Rack Quote for Your Memphis Warehouse
Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (901) 417-6960.
Memphis Pallet Rack
2298 Young Ave.
Unit #389
Memphis, TN 38104
(901) 417-6960Monday - Saturday: 8:00 AM - 6:00 PM
Memphis Pushback Rack Questions
Other Rack Types We Supply in Memphis

Pallet Rack
Every pallet reachable, every time. The baseline we size everything else against.
View details
Pallet Flow Rack
Load one side, pick the other, and let gravity enforce first in, first out.
View details
Drive-In Rack
Fewer access aisles. The forklift enters supported lanes to store deep quantities of a small number of SKUs.
View details
Cantilever Rack
Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.
View details
Carton Flow Rack
Cases advance to the picker instead of the picker hunting for cases.
View details
Warehouse Relocation
Teardown, labeling, transport coordination, and reinstallation of pallet rack and warehouse storage systems in your next building.
View detailsNearby Areas We Also Serve
Our delivery and installation territory covers west Tennessee, north Mississippi, and eastern Arkansas, so one team can handle multiple buildings for the same company.
Where We Work
Located in Memphis, we serve the entire Greater Memphis region with industrial pallet racks and warehouse storage solutions.
Memphis Pallet Rack
Address
2298 Young Ave.
Unit #389
Memphis, TN 38104
Phone
(901) 417-6960Business Hours
Monday - Saturday: 8:00 AM - 6:00 PM
Sunday: Closed
Need Pushback Rack in Memphis?
Call (901) 417-6960 or request a quote and we will get a layout started.